CLEAN AND CHECK
- CLEAN AND CHECK FEES
WILL NOT BE BILLED ON APPROVED REPAIR
- ALL REPAIRS WILL
BE ESTIMATED
- ESTIMATES AT NO ADDITIONAL
CHARGE
LENS $15.00
- Clean front optic
- Clean rear optic
- Test focus operation
- Test aperture function
- Check knobs and tighten
rear cluster screws
- Replace user o-rings
(additional charge for o-rings) & clean o-ring seat
- CLEAN AND CHECK +
FOCUS $25.00
- ALL ABOVE PLUS:
- Focus test with collimator
using factory, conversion optics
ALL FOCUS ADJUSTMENTS
AND REPAIRS WILL BE ESTIMATED
NIK V / NIK-IV-A CLEAN
AND CHECK $35.00
- Includes vacuum pressure
test
- Minor Cleaning
- Electronic shutter speed
test
- Light meter test
- Auto function test
- TTL test (no TTL test
performed on IV-A)
- MINOR ADJUSTMENTS
INCLUDED
- Optical cleaning (external)
- Film take up + rewind
test
- Installation of user
o-rings (additional charge for o-rings)
- All needed repairs will
be estimated
- ANNUAL SERVICE-PLEASE
REFER BELOW
NIK I-II-III CLEAN AND
CHECK $25.00
- Check shutter speeds
- Vacuum test
- Optical cleaning-external
- Housing cleaning
- User o-rings installed
(additional charge for o-rings)
- ANNUAL SERVICE-PLEASE
REFER below
ANNUAL INSPECTION MMII
& MMIIEX Yearly $35.00
MX-10 Yearly $25.00
- Remove internal assembly
- Inspect housing tighten
drive screws
- Clean o-ring seats
- Install new user set
o-rings (included in price)
- Pressure test
- Test roll of film for
advance and rewind check
- Report any lubrication
or cleaning issues
- ANNUAL SERVICE- PLEASE
REFER TO PAGE 4
HOUSINGS CLEAN
AND CHECK $35.00
- Evaluate for usability
- Minor lubrication
- Pressure test in water
- Vacuum test if available
- Minor port cleaning
- TTL test function test
if camera sent
- If not, evaluate with
shop camera as well as possible
- User o-rings installed
(additional charge for o-rings)
- ANNUAL SERVICE-
PLEASE REFER TO PAGE 5
STROBE CLEAN AND CHECK
$15.00
- Check batteries
- Battery contacts-minor
cleaning
- Minor cleaning
- User o-rings replacement
(additional charge for o-rings)
- TTL test
- Cord test-only if customer
provides cord
- Clean sync port contacts
- Thread cleaning
- Minor lubrication-user
o-ring replacement (additional charge for o-rings)
- ANNUAL SERVICE- PLEASE
REFER BELOW
MACRO TUBES SET- CLEAN
AND CHECK $7.00
- Install user o-rings
(additional charge for o-rings)
- Lubricate screws
- Clean o-ring seats
- Minor adjustments of
framers
- OPTICAL ADJUSTMENT-
$20.00
- CUSTOMER MUST SEND
PROPER LENS IN FOR OPTICAL ADJUSTMENT
- Test preformed in water
with your lens, tube and framer
- FULL SET OF 1:3 THRU
2:1 $40.00
- REPAIRS WILL BE ESTIMATED
ANNUAL
SERVICE
NIK V- Every 1-2 years
$140.00
- Replace all internal
(dynamic) o-rings-seals the moving parts
- Replace all user o-rings-lens,
back door, battery clip, sync port plug
- Clean all o-ring seats
- Lubricate all dynamic
portions of internal assembly
- Clean and polish external
housing
- Clean optics
- Calibrate, adjust light
meter
- Calibrate and adjust
auto function
- Test and report manual
shutter speeds
- Vacuum test-dynamic
dry test
- High pressure water
test to 150ft.
- Test roll of film for
rewind and film advance test
- TCXN-TTL test and adjustment
- Report any lubrication/cleaning
issues
NIK
IV-A- Same as Nik V, except NO TTL TEST $125.00
NIK
I-II-III Every 3 years or less $100.00
- Replace user o-rings-main
o-ring
- Replace dynamic o-ring-Lens,
rewind film advance
- Clean all o-ring seats
- Polish and clean external
housing
- Lubricate counter rewind
- Polish optics
- Minor counter adjustment
- Test and report shutter
speeds
- Minor adjustment shutter
speeds
- Vacuum test-dynamic
dry test
- High pressure water
test to 150ft.
- Strobe sync test
- Test roll of film for
rewind and film advance test
- Inspect and polish optics-complimentary
inspection of lenses
- Report and lubrication/cleaning
issues
MOTOR
MARINE - MMII- MMII EX $100.00 Every 3 years or less MOTOR MARINE MX-10 $ 50.00
Every 3 years or less
- Replace all internal
dynamic o-rings-seals the moving parts
- Replace all user o-rings
- Clean all o-ring seats
- Lubricate internal assembly
- Clean and polish internal
housing
- Clean optics
- Test and report manual
shutter speeds
- Vacuum test-dynamic
dry test
- High pressure water
test to 150 ft.
- Test roll of film for
rewind and film advance function
- Report any lubrication/cleaning
issues
ANNUAL
SERVICE ON STROBE
- Replace user o-rings
- Replace dynamic and
factory static o-rings
- Replacement of O2 scrubber
and dessicant if used by manufacturer (Nikon)
- Clean sync port pins
- Clean all threads
- TTL test
- Pressure test to 150
ft. in water
- General clean and check
of system
- Includes clean and check
of cord (o-rings additional)
ANNUAL
SERVICE ON HOUSING
- Servicing all control
glands
- Replacing all seals
- Polish control shafts
for corrosion
- Testing and correcting
sync circuit function
- Dynamic vacuum and pressure
test-PORT MUST BE INCLUDED
- Adjust alignment of
controls to camera
- FOR BEST CONTROL ALIGNMENT,
PLEASE INCLUDE CAMERA
- INCLUDE PORT FOR PRESSURE
TESTING
